d2cb59a429
CROSS_COMPILE_ENABLED is not yes. |
||
---|---|---|
doc | ||
etc | ||
man | ||
src | ||
CHANGES | ||
config.in | ||
Configure | ||
COPYING | ||
LICENSE | ||
Makefile | ||
README | ||
TODO |
* README * * Copyright (C) 1999 AbsoluteValue Systems, Inc. All Rights Reserved. * -------------------------------------------------------------------- * * linux-wlan * * The contents of this file are subject to the Mozilla Public * License Version 1.1 (the "License"); you may not use this file * except in compliance with the License. You may obtain a copy of * the License at http://www.mozilla.org/MPL/ * * Software distributed under the License is distributed on an "AS * IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or * implied. See the License for the specific language governing * rights and limitations under the License. * * Alternatively, the contents of this file may be used under the * terms of the GNU Public License version 2 (the "GPL"), in which * case the provisions of the GPL are applicable instead of the * above. If you wish to allow the use of your version of this file * only under the terms of the GPL and not to allow others to use * your version of this file under the MPL, indicate your decision * by deleting the provisions above and replace them with the notice * and other provisions required by the GPL. If you do not delete * the provisions above, a recipient may use your version of this * file under either the MPL or the GPL. * * -------------------------------------------------------------------- * * Inquiries regarding the linux-wlan Open Source project can be * made directly to: * * AbsoluteValue Systems Inc. * info@linux-wlan.com * http://www.linux-wlan.com * * -------------------------------------------------------------------- * * Portions of the development of this software were funded by * Intersil Corporation as part of PRISM(R) chipset product development. * * -------------------------------------------------------------------- Description: The linux-wlan package is a linux device driver and subsystem package that is designed to provide the full range of IEEE 802.11 MAC management capabilities for use in user-mode utilities and scripts. The package currently supports the Intersil Prism2 11Mb/s reference design PCMCIA wireless LAN (WLAN) card. For a list of elements that are still undone, see the TODO file in this directory License: See the COPYING and LICENSE files. Top level directory for linux-wlan-ng: ./doc - source distribution documentation ./man - man pages ./etc - scripts used at run-time ./src - source code for various components Note: Some of the subdirectories have empty README files. This means we haven't gotten to the contents of these directories. The empty README is just a trick to prevent CVS from pruning the directory. DISCLAIMER!!! prism2dl This utility is used for loading firmware images into prism2 cards. DO NOT USE IT! UNLESS YOU KNOW EXACTLY WHAT YOU ARE DOING. This utility has the capability to damage a card in a way that can only be repaired by the manufacturer. This software has currently been tested on the following configurations: linux-2.2.9 + pcmcia-cs-3.1.8 + RedHat6.0 linux-2.2.12 + pcmcia-cs-3.0.14 + RedHat6.1 The following build and install instructions assume you have configured source code for both the linux kernel package and pcmcia-cs package installed on your system. It's important that the configured code for these packages match the kernel and pcmcia-cs you currently have running. Build Instructions: 1) untar the package using the command: tar zxvf linux-wlan-ng-X.Y.Z.tar.gz 2) Make sure you have configured kernel and pcmcia sources on your system. 3) To clean up any unwanted files accidentally included in the tar package, run 'make clean'. If make clean behaves badly (infinite loop, for example), you may have a date/time mismatch. Run the command: find . -type f -exec touch {} \; to fix the date&time stamps, then run 'make clean' again. 4) To configure the linux-wlan-ng package, run 'make config' and respond to the questions. The defaults should be sufficient for most users. 'make config' must be run after a 'make clean' and before 'make all'. 5) To build the package, run 'make all' 6) To install the package, run 'make install' (as root). 7) Edit the /etc/pcmcia/wlan-ng.opts file to configure. These options are set every time you insert a card. If you want to change an option after the initial configuration, a) pop your card out, b) alter the file, c) insert your card. For more information see the file(s) linux-wlan-ng*/doc/config.* 8) Edit your network.opts file to set up your IP settings. Note: for a station, the SSID you're connecting to will be appended to the current pcmcia scheme name. You can use this to have different IP setups for different wireless LANs you connect to (e.g. home vs. work). 9) Restart pcmcia-cs with the command: /etc/rc.d/init.d/pcmcia restart 10) Insert the card. For most cards, a solid LED indicates that the SSID you specified was found, a bss was joined, and the firmware completed the authenticate and associate processes. 11) Run ifconfig and route to determine if your IP and route settings are listed as you wanted them. It's also a good idea to look at the file /etc/resolv.conf to see if your nameserver address has been set up correctly. 12) If you are trying to set up an AP, you will need bridging support compiled into your kernel. You will also need the brcfg utility. A version of this utility can be found on the AVS ftp site. ftp://ftp.absoval.com/pub/brcfg